Delt TS350 Bedienerhandbuch

INSTRUCTION MANUALTo learn more about DELTA MACHINERY visit our website at: www.deltamachinery.com.For Parts, Service, Warranty or other Assistance,pl

10DUST COLLECTION CONNECTORDo not operate this machine without the dust collection connector mounted.1. - Adapter Plate2. - Dust Collection Hood3.

Do not operate the machine without the dust collector attached.11Fig. 3Fig. 4Fig. 5Fig. 6ACDFEDGGDUST COLLECTION CONNECTORThe TS350 is supplied with a

121. Turn the saw table face down on cardboard to protect the table surface. Align the four holes in the saw cabinet with the four holes in the stan

131. Loosen the two screws and remove the table insert (A) Fig. 13. IMPORTANT: Do not lose the two rubber washers (L) located under table insert (A).

14GFEDCBAHAFEMLKHDGFig. 16Fig. 17Fig. 18Fig. 19Fig. 20Fig. 21PBCDSTVWAPCRXJEDE

151. Insert the handle (A) Fig. 22 into the threaded hole (B) in the rip fence (C)2. Insert a flat-head screwdriver into the rip fence handle (A) Fi

16You can make minor adjustments to the cursor (E) Fig. 26 by loosening the two screws (G), adjusting the cursor left or right, and tightening the two

176. Align the hole in the blade guard and splitter assembly (E) Fig. 29 with the hole in the splitter bracket (C). NOTE: Make certain that the two p

18The switch (A) is located on the front panel of the saw cabinet, as shown in Fig. 35. To turn the saw “ON”, move the switch up to the “ON” position.

ADJUSTING THE 90° AND 45° POSITIVE STOPSYour saw is equipped with positive stops that will rapidly position the blade at 90° and 45° to the table. To

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basi

20MITER GAUGE OPERATION AND ADJUSTMENTS1. Your miter gauge is equipped with individually adjustable index stops at 90° and 49° right and left. Make a

2121Common sawing operations include ripping and cross cutting. As with all power machines, a certain amount of danger is involved with the operation

2222RIPPINGRipping is the operation of making a lengthwise cut through a board (Fig. 51) Use the rip fence (A) to position and guide the work. Place t

23Attach the dado head set (D) Fig. 61 to the saw arbor.Use the accessory dado table insert (E) Fig. 67 in place of the standard table insert. The bla

24STORING THE RIP FENCEYou can store the rip fence (B) Fig. 63 on the holder bracket.STORING THE MITER GAUGE AND WRENCHThe two holder brackets hold th

25PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TO PUSH 1/4" WOODCUT OFF HERE TO

26TROUBLESHOOTINGFor assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or call the DELTA Machine

27A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service St

28Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

3It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. Th

4GENERAL SAFETY RULESREAD AND UN DER STAND ALL WARNINGS AND OP ER AT ING IN STRUC TIONS BE FORE USING THIS EQUIP MENT. Failure to follow all instructi

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.1. D

6Fig. A Fig. BGROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESGROUNDED OUTLET BOXGROUNDING MEANSADAPTERPOWER CONNECTI

7EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grou

81. Table Saw2. Extension Wing (2)3. Rip Fence4. Miter Gauge5. Rip Fence Handle6. Handwheel Lock Knob (2)7. M10 Flat Washer (2)8. Handwheel (2)9. Ri

9For Blade Guard and Splitter Assembly1. Splitter Bracket2. 5/8" Flat Washer (2)3. M12 x 1.75 Hex Nut (2)4. M6 x 1x20mm Hex Head Screw5. 1/4&